Klubersynth UH1 6-100
Your requirements - our solution.
Klubersynth UH1 6-100 is a synthetic high-performance gear oil based on polyglycol satisfying the growing requirements and increasing power density of modern gears. UH1 6-100 includes KlüberComp Lube Technology, i.e. it is based on especially high-grade raw materials and advanced additives, enabling maximum performance in the lubrication of all gear components.
This oils are NSF H1 registered and therefore comply with FDA 21 CFR § 178.3570. The lubricants were developed for incidental contact with products and packaging materials in the food-processing, cosmetics, pharmaceutical or animal feed industries. The use of Klubersynth UH1 6-100 oils can contribute to increase reliability of your production processes. We nevertheless recommend conducting an additional risk analysis, e.g. HACCP.
It is certified according to ISO 21469
It clearly exceeds CLP requirements according to DIN 51517-3. Corresponding gears can be switched to Klubersynth UH1 6-100 without prior consultation with the gear manufacturer provided the general application notes are observed.
Klubersynth UH1 6-100 offers high scuffing load capacity. Gears are sufficiently protected against scuffing even at extremely high peak loads, vibrations or oscillations, or if no running-in was performed. The excellent wear protection of both gears and rolling bearings ensures that the service life calculated for the lubricated components is achieved, leading to lower maintenance and repair costs.
The oil's high micropitting resistance of GFT ≥ 10 according to FVA 54/7 offers sufficient protection to gears that are subject to high loads and would normally be susceptible to this type of damage.
Klubersynth UH1 6-100 offers a much longer service life than mineral oils due to the excellent ageing and oxidation resistance of the selected raw materials; thus service intervals can be extended and maintenance costs reduced.
In certain applications, even lifetime lubrication is possible. The product's low foaming tendency and anti-corrosive properties enable problem-free gear operation. Freudenberg seals made of 72 NBR 902, 75 FKM 585, 75 FKM 260466 and 75 FKM 170055 are resistant to Klübersynth UH1 6. Leakage and oil contamination are prevented.
The excellent viscosity-temperature behaviour supports the formation of a sufficient lubricant film across a wide service temperature range, even at elevated and high temperatures. Therefore, a single viscosity grade can cover both low and high temperatures in many applications.
The optimised friction behaviour enabled by the carefully selected base oils based on polyglycol reduces power loss and improves gear efficiency, especially in worm gears. Due to the optimised additives, wear are reduced and a very low wear intensity according to DIN 3996 (calculation of load capacity of worm gears) is achieved. Klubersynth UH1 6-100 is approved by Siemens-Flender, Siemens Geared Motors, SEW Eurodrive, Getriebebau Nord, Stöber Antriebstechnik, Lenze, ZAE Antriebssysteme, Baldor, Boston Gear, Bonfiglioli, Watt Drive, etc
Klubersynth UH1 6-100 - Benefits
- Registered as NSF H1 and certified according to ISO 21469
- High scuffing protection
- Good wear protection for gears and rolling bearings
- High micropitting resistance
- Good shear stability for reliable lubricant film formation
- Optimised for the lubrication of worm gears
- Excellent ageing and oxidation resistance
- Wide service temperature range due to good viscosity-temperature behaviour
- Low foaming tendency
- Energy savings due to optimised friction behaviour
- Good elastomer compatibility
- Approvals by numerous gear OEMs
Klubersynth UH1 6-100 Application
- Klubersynth UH1 6-100 oil is used for the lubrication of highly loaded spur, bevel and planetary gears, rolling and plain bearings as well as all types of toothed couplings, especially when exposed to high temperatures.
- Klubersynth UH1 6-100 oil was especially developed for the lubrication of worm gears with steel/bronze pairings.
- It can also be used for the lubrication of lifting, drive and transport chains.
Klubersynth UH1 6-100 Application notes
UH1 6-100 can be applied by means of immersion, immersion circulation or injection.The use of drip-feed oilers, brushes, oil cans or suitable automatic lubricating systems is also possible. When using automatic lubricating systems, please note the manufacturer's instructions regarding the maximum permissible viscosity. The low-viscosity varieties are also used for oil mist lubrication.
Klubersynth UH1 6-100 is not miscible with mineral oil or synthetic hydrocarbons. Prior to switchover, lubrication points should be cleaned, or gears or enclosed systems be flushed with the Klubersynth UH1 6-100 oil to be used.
Klubersynth UH1 6-100 is neutral towards ferrous and nearly all non-ferrous metals.
There may be increased wear when the contact surfaces of design elements made of aluminium or aluminium alloys are exposed to dynamic loads. If necessary, preliminary wear tests should be carried out.
For use at permanent temperatures of 80 °C max., seals made of NBR may be used. For higher temperatures, seals made of FKM should be chosen. It should be noted that elastomers one or several manufacturers can behave differently; therefore tests should be performed.
When applying Klubersynth UH1 6-100 oil we recommend the use of two-component paints (reaction paints) for interior coating. Oil gauge glasses should preferably be made of natural glass or polyamide materials. Other transparent plastics, e.g. Plexiglas, have a tendency to crack under stress. The suitability of materials used in contact with UH 1 600 oil should be tested, especially prior to series application
Technical data of Klubersynth UH1 6-100
| Product data | Klübersynth UH1 6-100 |
|---|---|
| Article number | 096094 |
| Marking acc. to DIN | CLP PG 100 |
| Classification acc. to ISO | CKC 100 |
| NSF-H1 registration | 137 872 |
| Lower service temperature | -35 °C / -31 °F |
| Upper service temperature | 160 °C / 320 °F |
| Density, at 15 °C | approx. 1 040 kg/m³ |
| Kinematic viscosity at 20 °C | approx. 250 mm²/s |
| Kinematic viscosity at 40 °C | approx. 100 mm²/s |
| Kinematic viscosity at 100 °C | approx. 19.5 mm²/s |
| Viscosity index | >= 190 |
| ISO viscosity grade | 100 |
| Flash point, DIN EN ISO 2592, | >= 220 °C |
| Pour point, DIN ISO 3016 | <= -40 °C |
| Foam test, ASTM-D 892, ISO 6247, sequence I/24 °C | <= 100/10 ml |
| Foam test, ASTM-D 892, ISO 6247, sequence II/93.5 °C | <= 100/10 ml |
| Foam test, ASTM D 892, ISO 6247, sequence III/24°C | <= 100/10 ml |
| Copper corrosion, DIN EN ISO 2160, 24 h/100°C | 1 - 100 corrosion degree |
| Anticorrosive properties on steel, DIN ISO 7120, method A, steel, 24 h/60 °C | no rust corrosion degree |
| Ageing properties, ASTM D 2893, increase in viscosity | <= 6 % |
| FZG scuffing test, DIN ISO 14635-1, A/8.3/90, scuffing load stage | >= 12 |
| FAG FE8 rolling bearing test, DIN 51819-3, D 7,5/80-80, wear of cage | <= 200 mg |
| FAG FE8 rolling bearing test, DIN 51819-3, D 7,5/80-80 | <= 30 mg |
| Minimum shelf life | 36 months |
Where to buy Klubersynth UH1 6-100 ?
As an authorized distributor, Hicotech provides genuine Klubersynth UH1 6-100 and various other industrial products including lubricating oils, greases, chemicals, and more. We offer consultation services and competitive pricing. Please don't hesitate to contact us for further information.
Contact Information:
Hotline/Zalo. 094 526 1931
Website. Hicotech.com.vn
Email: Sale@hicotech.com.vn
Có 0 bình luận, đánh giá về Klubersynth UH1 6-100
TVQuản trị viênQuản trị viên